A1 Cardone 20-906R Power Steering Pump in Canada

Buyer fitment guide only intended as reference. Please use catalogue search by vehicle to ensure proper fitment.

Chrysler 4782207AC
Chrysler 4782207AD
Dodge 4782207AC
Dodge 4782207AD

CARDONE Remanufactured Power Steering Pumps are engineered to meet or exceed O.E. performance. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Every unit undergoes a hydraulic efficiency test to ensure reliable, long-lasting performance.
As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%.
All critical components (campacs, spool valves, etc.) are triple-tested to ensure product reliability.
All units are built with 100% new O-rings and premium-grade HNBR seals to prevent leaks. HNBR does not break down at high temperatures like conventional seal material.
FInal pump assembly is computer-tested to measure pressure, bypass, fluid flow, valve operation, steering effort and noise to ensure reliable performance.
Shafts are surfaced to precise specifications to eliminate premature seal wear and extend pump life.
Units are supplied with 100% tested and calibrated pressure relief valves.

Housing Material	Aluminum/Cast Iron
Outlet Thread Size	16x1.5
Pulley Belt Type	Serpentine
Package Contents	Hydraulic Pump; Instruction Sheet; Sealing Kit
Product Condition	Remanufactured
E-Waste	No
Prop 65	No
SDS Required	No
Contains Electronic Components?	No
Is item a chemical?	No
Is or contains a battery?	No
Is or contains a bulb?	No
Is the item CARB affected?	No
FAQ_Q1	Why is the pump making a whining noise all of the time?
FAA_A1	A whining pump is usually caused by air in the power steering system. Inspect the reservoir for proper fluid level. If fluid has foam or air bubbles present, air has entered the system or has not been properly bled (ensure all hoses/clamps are tight). Some systems require special vacuum bleeding procedures.
FAQ_Q2	Why do I still have hard steering in one direction after I replaced the pump?
FAA_A2	The problem is most likely in the steering unitâˆ’the pump does not know left from right. Check for binding steering components and repair as necessary.
FAQ_Q3	I bought a replacement power steering pump and my original pulley has a loose fit on the replacement pump shaft. What should I do?
FAA_A3	The pulley may have cracked upon removal. If the shaft was mushroomed before removing the pulley, it has now enlarged the bore in the pulley. The pulley must be replaced.
FAQ_Q4	I only have assist when increasing engine rpm after installing the replacement pump. What's causing this?
FAA_A4	There may be debris in the flow control valve bore not allowing the flow control valve to move as it should. (Valve and bore are located behind the high pressure fitting on the pump). The system must be checked for contamination and flushed.
FAQ_Q5	Should I ever change my fluid, even though nothing is wrong?
FAA_A5	Yes. Some O.E. manufacturers recommend that power steering fluid be changed at 50,000 miles and continue at that interval. Just like engine oil, power steering fluid will eventually break down and carry suspended contaminants from component wear and breakdown. Follow your vehicle's O.E. manufacturer's recommendations on fluid change intervals.
UPC	00884548246751
Origin Country:	MX
Weight:	5.77 lbs (2.62 kg)
Package Length:	7.9" (20 cm)
Package Width:	6.1" (15.6 cm)
Package Height:	5.3" (13.3 cm)

1 Year Warranty

A1 Cardone 20-906R Power Steering Pump

Remanufactured Power Steering Pump