A1 Cardone 18-4652XR Disc Brake Caliper
Remanufactured Unloaded Caliper w/Color Coating
Brand: A1 Cardone
Stock #: 184652XR
Condition: Remanufactured
Made in USA
UPC: 082617667555
Weight: 13.51 lbs (6.14 kg)
Accepted Payments: Visa, MasterCard, PayPal
Buyer fitment guide only intended as reference. Please use catalogue search by vehicle to ensure proper fitment.
- OEM Part Number BE8Z3A130A
- MOOG Chassis Products ES800985
- NAPA Chassis Parts 2693815
- MAS Industries TO21002
- Ford F75Z2B120AF
- Ford XL3Z2B120EA
- Lincoln F75Z2B120AF
- Lincoln XL3Z2B120EA
- A plastic cap plug protects every brake port thread to ensure a trouble free installation.
- As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
- Mounting bracket is included where applicable for a hassle-free installation.
- New banjo bolts are included where applicable to ensure a perfect fit and quick installation.
- New bleeder screws provide trouble-free bleeding and a positive seal.
- New stainless steel hardware clips and new mounting pins are included where applicable.
- New washers are included where applicable for a proper seal.
- Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%.
- Pistons are durable, resistant to cracking or pitting and handle great loads.
- Rubber seals are replaced with new high temperature EPDM rubber for extended life and optimum performance.
- Coated Calipers feature an exclusive weather-proof coating that stops rust from forming and a showroom appearance.
- For a premium appearance and enhanced protection against corrosion and rust, CARDONE Color-Coated Calipers feature a weather-proof coating available in red or yellow. Each caliper is built with brand-new, premium components to guarantee exceptional braking performance and longevity. They are also tested to meet rigorous standards and packaged with a complete set of brand-new hardware for a simple, complete installation. Caliper bracket is included when applicable.
| Bleeder Screw Cap Included | No |
| Rust Resistant Coating | Yes |
| Dust Boots Included | Yes |
| Bleeder Thread Size | 3/8x24 |
| Inlet Port Size | 9.52125 |
| Inlet Port Size | 0.375 |
| Product Condition | Remanufactured |
| Package Contents | Caliper; Instruction Sheet; Bracket; Hardware Kit |
| Prop 65 | No |
| E-Waste | No |
| SDS Required | No |
| Contains Electronic Components? | No |
| Is item a chemical? | No |
| Is or contains a battery? | No |
| Is or contains a bulb? | No |
| Is the item CARB affected? | No |
| FAQ_Q1 | What colors are the Coated Calipers available in? |
| FAA_A1 | Our Coated Calipers are currently available in Silver, Blue, Yellow and Red. |
| FAQ_Q2 | Can I switch out a Phenolic Piston Caliper for a Steel Piston Caliper or vice versa? |
| FAA_A2 | Not recommended. The O.E. manufacturers specified steel or phenolic pistons based on the intended use of the vehicle. It is recommended that the installer follow the manufacturer’s recommendations. |
| FAQ_Q3 | What type of fluid should I use: DOT 3, DOT 4, or DOT 5? |
| FAA_A3 | As a rule, always use brake fluid recommended by O.E. The fluid type is stamped on the master cylinder reservoir lid. Always use new fluid in a sealed container. |
| FAQ_Q4 | Car pulls to one side during braking. Why? |
| FAA_A4 | Inspect both calipers for binding or sticky slides or pins. Also ensure that brake hoses are not collapsed or restricted and inspect steering/suspension components for proper operation. |
| FAQ_Q5 | Brakes squeal all of the time. What's causing the squeal? |
| FAA_A5 | Brake squeal can be caused by improper installation of the brake pads, improperly installed brake hardware and improper brake rotor finish. |
| FAQ_Q6 | Could calipers be the cause of a low brake pedal? |
| FAA_A6 | A symptom of a low brake pedal is usually caused by air in the system, misadjusted rear brake shoes, deteriorated brake hose(s) or a defective master cylinder. |
| FAQ_Q7 | What type of grease is used on floating caliper mounting pins? |
| FAA_A7 | A silicone grease is used on floating caliper mounting pins. |
| FAQ_Q8 | Do all of your Calipers come with the new hardware and a mounting bracket for installation? |
| FAA_A8 | New hardware is included with all of our Calipers however the mounting bracket is an added option depending on part number and application. Mounting Brackets are also sold separately for most applications. |
| UPC | 082617667555 |
| Origin Country: | US |
| Weight: | 13.51 lbs (6.14 kg) |
| Package Length: | 10.8" (27.3 cm) |
| Package Width: | 7.1" (18.1 cm) |
| Package Height: | 6.5" (16.5 cm) |
1 Year Warranty