A1 Cardone 18-4021 Disc Brake Caliper
Remanufactured Unloaded Caliper
Brand: A1 Cardone
Stock #: 184021
Condition: Remanufactured
Made in USA
UPC: 082617010658
Weight: 9.31 lbs (4.23 kg)
Accepted Payments: Visa, MasterCard, PayPal
Buyer fitment guide only intended as reference. Please use catalogue search by vehicle to ensure proper fitment.
- MAS Industries TI72010
- Qualis ES4470
- Xpress Automotive Supplies XEV80692
- Ingalls Engineering IEV80692
- OEM Part Number 34116FC011
- AutoZone ES80692
- Ingalls Engineering IEV80804
- AutoZone ES80804
- Deeza LNA604
- OEM Part Number 2C5Z3280AA
- MOOG Chassis Products EV80809
- NAPA Chassis Parts 2693263
- Transbec TEV80809
- MAS Industries TI85270
- Ingalls Engineering IEV80809
- NAPA Master Ride Chassis ES80809
- Deeza TYA617
- MOOG Chassis Products EV80893
- TRW Steering and Suspension Parts JAR1180
- Transbec TEV80893
- MAS Industries TI74150
- Mcquay-Norris ES4268
- Mcquay-Norris ES4268E
- OEM Part Number 4550309250
- NAPA Master Ride Chassis ES80893
- Beck/Arnley 1015319
- Beck/Arnley 1015319
- MOOG EV80809
- Oldsmobile 18003760
- Pontiac 18003760
- Chevrolet 18005264
- Chevrolet 18012308
- Chevrolet 18015427
- Chevrolet 18020903
- Buick 18005264
- Buick 18012308
- Buick 18015427
- GMC 18015427
- Cadillac 18005264
- Cadillac 18012308
- Cadillac 18015427
- Oldsmobile 18005264
- Oldsmobile 18012308
- Oldsmobile 18015427
- Pontiac 18005264
- Pontiac 18012308
- Pontiac 18015427
- As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
- Mounting bracket is included where applicable for a hassle-free installation.
- New banjo bolts are included where applicable to ensure a perfect fit and quick installation.
- New bleeder screws provide trouble-free bleeding and a positive seal.
- New stainless steel hardware clips and new mounting pins are included where applicable.
- New washers are included where applicable for a proper seal.
- Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%.
- Pistons are durable, resistant to cracking or pitting and handle great loads.
- Rubber seals are replaced with new high temperature EPDM rubber for extended life and optimum performance.
- A plastic cap plug protects every brake port thread to ensure trouble-free installation.
- Calipers are treated with a special formulated rust inhibitor and kept in the original equipment finish.
| Bleeder Screw Cap Included | No |
| Rust Resistant Coating | Yes |
| Dust Boots Included | Yes |
| Bleeder Thread Size | M10x1.5 |
| Inlet Port Size | 10.00366 |
| Inlet Port Size | 0.394 |
| Product Condition | Remanufactured |
| Package Contents | Caliper; Instruction Sheet; Hardware Kit |
| Prop 65 | No |
| E-Waste | No |
| SDS Required | No |
| Contains Electronic Components? | No |
| Is item a chemical? | No |
| Is or contains a battery? | No |
| Is or contains a bulb? | No |
| Is the item CARB affected? | No |
| FAQ_Q1 | Can I switch out a Phenolic Piston Caliper for a Steel Piston Caliper or vice versa? |
| FAA_A1 | Not recommended. The O.E. manufacturers specified steel or phenolic pistons based on the intended use of the vehicle. It is recommended that the installer follow the manufacturer’s recommendations. |
| FAQ_Q2 | What type of fluid should I use: DOT 3, DOT 4, or DOT 5? |
| FAA_A2 | As a rule, always use brake fluid recommended by O.E. The fluid type is stamped on the master cylinder reservoir lid. Always use new fluid in a sealed container. |
| FAQ_Q3 | Car pulls to one side during braking. Why? |
| FAA_A3 | Inspect both calipers for binding or sticky slides or pins. Also ensure that brake hoses are not collapsed or restricted and inspect steering/suspension components for proper operation. |
| FAQ_Q4 | Brakes squeal all of the time. What's causing the squeal? |
| FAA_A4 | Brake squeal can be caused by improper installation of the brake pads, improperly installed brake hardware and improper brake rotor finish. |
| FAQ_Q5 | Could calipers be the cause of a low brake pedal? |
| FAA_A5 | A symptom of a low brake pedal is usually caused by air in the system, misadjusted rear brake shoes, deteriorated brake hose(s) or a defective master cylinder. |
| FAQ_Q6 | What type of grease is used on floating caliper mounting pins? |
| FAA_A6 | A silicone grease is used on floating caliper mounting pins. |
| FAQ_Q7 | Do all of your Calipers come with the new hardware and a mounting bracket for installation? |
| FAA_A7 | New hardware is included with all of our Calipers however the mounting bracket is an added option depending on part number and application. Mounting Brackets are also sold separately for most applications. |
| UPC | 082617010658 |
| Origin Country: | US |
| Weight: | 9.31 lbs (4.23 kg) |
| Package Length: | 9.6" (24.3 cm) |
| Package Width: | 7.3" (18.4 cm) |
| Package Height: | 5.3" (13.3 cm) |
1 Year Warranty